One kitchen equipment with the highest use rates in the microwave, which is used often. Throughout the day, it is used to cook and heat meals.
To avoid any issues in the kitchen, it is crucial to maintain it in top shape.
However, owing to regular use, it could sometimes have issues.
One of these issues is a broken microwave display.
You may sometimes have problems with the display that shows the temperature, time, etc.
You may be unable to estimate the time remaining to cook, etc., without the time display and other information.
There are a variety of potential causes for this.
Your Frigidaire microwave display may stop working due to numerous reasons and may involve faulty control board, power supply, and electrical components.
Damaged Temperature and monitor fuse can also cause this display problem.
In some circumstances, you may be able to handle the problem by yourself.
The following are some possible causes and fixes for a malfunctioning microwave display.
Can You Fix the Display on a Microwave?
Microwave may looks like an appliance that is difficult to take apart, in reality it is not!
In fact, in terms of appliance repair, replacing the control panel and display on a microwave is actually one of the simpler repairs you can do.
Essentially, you just require to remove the outer casing on the microwave to get access of it.
You can then simply remove the keypad and display to make replacement.
Causes For Frigidaire Microwave Display is Not Working
Do not worry if your Frigidaire microwave display is not working.
Read our section on causes to trace the fault.
Fault in the Frigidaire Microwave display is crucial and must be tackled technically.
Below is a list of common causes behind the abnormal Frigidaire Microwave display.
Faulty Main Control Board
An unreliable main control board is the first potential cause of a malfunctioning microwave display.
There may be missing numbers or lines if the primary control board or circuit board malfunctions.
A defective capacitor or a missing solder are the typical culprits for this issue.
You may check the appliance’s internal circuit to see if there is a broken line for this.
Faulty Power Supply
An inadequate power supply is another potential reason the microwave display isn’t functioning.
Your microwave’s display may not be working correctly if the power supply to the device isn’t enough.
Faulty Temperature and Monitor Fuse
You must also check the temperature and the monitor fuse if the microwave display isn’t functioning.
Make sure none of them is blown away.
The fuses for every kind and brand of the microwave will be placed in various locations throughout the appliance.
Failure of Electrical Components
The Panasonic microwave ovens have several electrical components like terminal diode that might be damaged by electrical disturbances.
To address the display issue with the microwave, more caution is needed.
Even though there are several electrical causes for component failure.
Fixes For Frigidaire Microwave Display Not Working
A crucial component of the microwave is the display.
The display is used to verify the instructions you’ve typed using button presses.
It indicates the power level, the remaining time, and your chosen setting.
It serves as the central, visible clock in many homes.
Few things are more unpleasant than when the display on your microwave abruptly stop functioning.
It may be entirely blank, show you a row of half-zeroes, or be so scrambled that you have to decipher the display to see the popcorn countdown.
We’re here to provide a simple tutorial for what to do if your microwave display stops functioning, no matter the issue.
Please follow below fixation steps if your Frigidaire microwave display is not working.
Check the Power Supply
Checking the power source and cord is the first step in diagnosing equipment.
There’s a possibility that your microwave is simply unplugged or powered by a tripped breaker if the screen has gone entirely blank and the buttons aren’t beeping anymore.
Start at the appliance’s rear.
Is the cable securely fastened and not frayed, exposed, or loose at the base connection?
Check the wall socket if the answer is no.
Has the plug been fully inserted into the wall? Does the cable’s end seem to be in good condition?
Push the pin in if it’s loose. Check the breaker if the plug appears to be in good shape.
It’s possible that your outlet lost power, not the plug, which was the cause.
Examine the breaker box. Flip a breaker’s “off” and “on” switches back and forth to reset it if it is at the center or facing the incorrect way.
Next, examine your microwave. Try connecting your microwave to a different outlet as the last check.
Secure Loose Wires
If there isn’t a power issue, your microwave’s display and control panel likely contain the problem.
You’ll need to take off the control panel to get to this.
Once there, you may look “under the hood” to see if any issues could be quickly rectified.
To avoid being shocked when you reach the cables beneath the panel, unplug your microwave from the wall.
Remember that even after disconnecting the appliance, the microwave’s capacitor might retain voltage for a considerable amount of time.
It could need a manual discharge, something you shouldn’t try without preparation and previous knowledge.
The top front of your microwave, which hides the front vent, should have mounting screws. Open the door after removing the screws, and pull the vent free.
You can see extra mounting screws holding the panel to the microwave cabinet with the door open.
After removing those screws, gently push the panel apart while pressing any edge clips.
The microwave and the panel will be connected via cables.
Firmly fasten these wires or unplug and re-plug each wire harness.
By using this technique, a loose wire may be fixed.
Reopen the panel and push until the clips click once all the wires are in place.
The vent cover and mounting screws, are returned.
Try the panel again after re-plugging the microwave. You could have just solved your issue.
Change Control Panel
Your last option is to think about having the control panel replaced if nothing else has worked.
Most of the time, replacing the complete panel assembly is preferable to attempting to figure out which individual minor electric component malfunctioned and how to repair it.
You will need to search for detailed information on this repair depending on the brand and model of your microwave if you decide to replace the panel.
It can also matter if your microwave is situated over the stove.
This will specify the location of your mounting screws and clips and the precise procedures to swap out one control panel with a replacement.
Of course, you’ll also need a proper replacement order for your microwave model.
Replace High Voltage Diode
When a diode fails, the display often seems to be problematic.
If the diode appears to be burned out, replace it.
If inspecting the diode yields no information, test it with a multimeter that is powered by a small battery or connect the battery and the diode in series.
Frigidaire Microwave Display Dim?- 2 Easy Ways to Brighten Microwave Display!
Power saving feature
If your Frigidaire microwave display is dim, your microwave might have on power saving feature.
You can try the power saving feature in the clock setting which causes your microwave display dim.
So, check whether the power saving feature is on or off.
Surface light setting
Your Frigidaire microwave display also gets dim due to surface light setting.
You need to check surface light setting if you facing the issue of dim display.
There is a surface light pad available to control the display light on your Frigidaire microwave.
There is a light bulb icon on the panel that has Hi, Med, Low setting.
On some other models of Frigidaire microwave, you have the option to press the pad once for getting bright light and twice for the night light.
If you press the SURFACE LIGHT three times, it will turn the light off.
If you feel the light is so dim, you can a contact electrician/ professional for a physical assessment of your microwave and diagnosis.
Sometimes physical inspection is the only way to tell if your appliance needs adjustment.
Alternatively, you can contact the manufacturer locate nearby you.
Frigidaire Microwave Display Dim But Microwave Works Fine?
If your microwave has dim display but works fine then there is issue with electronic control.
For resolving the issue, turn the breaker off for a few minutes and check if it is brighter display.
If it doesn’t, you need to replace control board.
Just replacing the control board may resolve your issue.
How to Reset Frigidaire Microwave?
Reset Frigidaire microwave using simple following steps:
1.Take hold of the plug on your Frigidaire and remove it from the outlet.
2. When ready, plug your oven back in after waiting around three minutes.
3. Switch the Frigidaire microwave on.
4. Pinning the Clock button sets the time. The dial displays the hours, minutes, and am/pm.
How to Reset Frigidaire Microwave Clock?
Follow simple steps to reset your Frigidaire microwave clock:
1. Plug your microwave into the socket by going to the outlet.
2. Wait up to five minutes before plugging your oven back in.
3. Play with the Clock button to start the appliance and set the time. You have time, minutes, and the am/pm slots available to dial and select the proper time.
Sources:
https://www.fixya.com/support/t12308383-frigidaire_microwave_display_not_working
https://www.youtube.com/watch?v=fs9nM8hppLQ
Related Articles:
Frigidaire Microwave Annoying Beep?
Frigidaire Microwave Fan Wont Turn Off?
