Is your Kenmore Elite refrigerator is displaying er 1f error code?
Then you came at right place to fix this issue!
Many of users experiencing this problem with their Kenmore refrigerator.
But why this error occurs?
When there is no signal from the icing fan motor to the main control board for more than 114 seconds, this error occurs.
Please inspect the fan in the rear of the freezer if you notice the code on the display. The fan’s job is to blow air toward the ice maker.
In certain circumstances, disconnecting a refrigerator and plugging it back in after around 5 minutes can resolve the problem.
If the problem reappears, it indicates that the fan is not running.
This might be due to ice forming and obstructing rotation.
In this scenario, normal defrosting should suffice: unplug the fridge for a day or so and let all of the ice to melt.
Let’s dive into detail.
What Does Mean er 1f on Kenmore Elite Refrigerator?
Error Code for “Kenmore Refrigerator” = Er 1F
“Error Condition” = the ice compartment’s fan failed.
Icing fan is clogged, and the ice fan motor is broken.
The wiring in the circuit is faulty, and the control board has failed.
Your refrigerator may be emitting some danger signals.
The lights on your refrigerator may be flickering or perhaps turning out completely.
This signifies that anything within your refrigerator isn’t working properly.
If you detect anything out of the ordinary, don’t be afraid to contact a professional appliance repair agency.
It’s crucial to remember that refrigerators aren’t built to endure indefinitely.
They typically have a lifespan of about ten years.
That is why it is critical to take proper care of them.
Before hiring a professional appliance repair agency to fix your fridge, make sure you read the handbook.
Causes for Kenmore Elite Refrigerator er 1f Code
This error “er 1f” number indicates that the ice maker blower fan is not functioning properly and so is not pushing air toward the ice maker.
There might be an issue with any of the following components: the main control board, the ice blower fan, the ice maker motor, the wire harness, or loose wiring somewhere.
As a result, the ice maker fails to create ice, resulting in leaks.
There are various possible causes for the fan to stop working:
- Faulty fan due to ice accumulation and fan obstruction
- Disconnection or loose or damaged wiring
- Fan motor failure
The main control board is not working correctly.
Error 1f is freezer fan fault.
This usually happens when either the rear board has gone bad or the freezer fan itself is bad and needs to be replaced.
To check what is causing the error you can start with checking the fan which is located behind the back wall inside the freeze.
The error “er 1f” will come in the Kenmore elite refrigerator due to many factors including:
- Wiring issue
- Board Parts issue
- Board Communication error
- Receiver Error from the icing fan to board
Wiring issue
The wiring between the board and the icing is damaged or the connections become weak over time.
This will cause the error “er 1f” in the Kenmore elite refrigerator.
Board Failure
The board failure can cause the communication cut down between the icing fan motora and main control board.
The error “er 1f” will appear on the Kenmore elite refrigerator
Fan motor Failure
“Kenmore elite refrigerator er 1f” error can also appear because of the failure of the icing fan motor and it won’t communicate with the main board.
The board will not be able to get the status of the fan.
Fan Clogging
The icing fan may be clogged because of the ice on it.
It may happen because of the moisture and frequent opening or leakage of the coolant.
This will cause the connection cut in the communication between the board and the fan.
The display will show the “er1” error on the Kenmore elite refrigerator.
The ice maker fan constantly blows cold air via its fan blades.
However, if the air contains too much moisture, frost and ice will form surrounding the fan.
Over time, the ice accumulation will get so massive that it prohibits the fan blade from spinning at all.
Apart from these errors, other error can also cause this error but they have very little probability including damage to the fan housing, untimely maintenance and manufacturing error.
Fixes For Kenmore Elite Refrigerator er 1f Code
The 1F or IF error number on an LG refrigerator indicates that the ice maker fan is malfunctioning.
This code is produced by ice accumulation at the fan or a malfunctioning ice maker fan motor.
Aside from that, the code might be caused indirectly by an issue with the door alignment or door gasket.
Fan Clogging fix
A buildup at your ice maker fan must be fully defrosted.
This procedure will take at least 8 hours, if not more, depending on the size of the accumulation.
To do so, empty the ice bin and leave the refrigerator doors open.
Then, disconnect your refrigerator and let it alone for at least 8 hours, or until the ice has melted away.
Fridge Seal Problems fix
Refrigerator doors are meant to seal tightly and keep cold air from exiting the compartments.
However, same doors also prevent warm air from entering the fridge and producing the ice accumulation detailed in the preceding section.
The door gasket is essential because it assists the door in forming a tight seal with the rest of the fridge’s body.
Door Misalignment fix
Refrigerator doors are meant to seal tightly and keep cold air from exiting the compartments.
However, same doors also prevent warm air from entering the fridge and producing the ice accumulation detailed in the preceding section.
The door gasket is essential because it assists the door in forming a tight seal with the rest of the fridge’s body.
Ice Motor Fail fix
Because the ice maker fan engine cannot be fixed, you must replace it.
The ice maker fan housing is linked to the freezer’s back panel.
To get to it, take all of the goods and shelves from the freezer.
Next, unthread the mounting screws and detach the rear panel from the tabs that keep it in place.
After removing the panel, unthread the screws that secure the fan motor to its housing on that panel.
With the screws removed, separate the fan’s electrical wires and remove the fan assembly.
How to Remove Kenmore Elite Refrigerator er 1f Error?
Resetting your refrigerator is as simple as turning it off and on again. That is, you will switch it off and on again as follows:
- First, switch off the fridge’s power supply.
- After then, turn off the appliance for at least 30 seconds. During this period, it will discharge any power within and clean its memory, including the error code.
- Finally, reconnect the fridge to the power supply.
By doing above measures you can remove the “Kenmore elite refrigerator er 1f” error.
Final Thoughts
Kenmore elite refrigerator er 1f error occurs when there is no signal from the icing fan motor to the main control board for longer than 114 seconds.
If you see the code on the display, please, check the fan in the back of the freezer.
The fan’s mission is blowing air toward the ice maker.
In some cases, the error can be cleared by unplugging a refrigerator and plugging it back after about 5 minutes.
Should the problem come back, it means that the fan is not running. This may be caused by ice building up and blocking the rotation.
In this case, general defrosting should work: unplug the fridge for a day or so and let all the ice melt
In this way you can resolve this annoying error.
Related Articles:
Frigidaire Refrigerator Sy Cf Error Code?
Frigidaire Refrigerator Beeping H1?