Countertop Blender

KitchenAid Blender Flashing Lights?- 6 Easy Methods to Fix It!

kitchenaid blender flashing lights
( Disclaimer: As an Amazon Associate, we earn commissions from qualifying purchases at NO additional cost to the customer.)                                          

A KitchenAid blender offers efficient and convenient ways to mix and blend various foods.

Anyone who has ever owned a blender would know how easy it is to make their favorite shakes and smoothies when you own an appliance like this.

KitchenAid makes numerous blender models, and some of the designs feature indicator lights on the appliance’s base.

So is your KitchenAid blender flashing lights suddenly?

This occurs due to overload your blender, electricity problem, stuck key, locked motor rotor.

Your Kitchenaid blender also blinks lights may due to if it is gets jammed or pitcher not secured to the base.

Keep reading to know more in detail the causes and its fixes.

Reasons – KitchenAid Blender Flashing Lights

The lights are directly or indirectly connected to many of the other components of the blender.

So when one of them breaks down, it affects the lights too.


If all of the indicator lights are flashing simultaneously on your KitchenAid blender, that means the gadget has been overloaded.

To reduce strain, the blender shuts down automatically when the items in the blender pitcher are too chunky to break down.

Change the blender position to “off,” open the pitcher, and take out some items inside.

You can separate them into smaller groups and blend them in batches.

Place the blender pitcher back on top of the blades.

If the lights stop flashing, your issue has been resolved.


Did you know that blenders can get jammed too?

The blending arms cannot turn and incorporate the pitcher’s contents when this happens.

If the indicator lights on your KitchenAid blender are blinking alternately, there might be a jam behind the issue.

To solve it, turn off the blender and open the pitcher.

Remove or break up the contents at the base of the jar to release the arms.

Consider the issue solved if the lights return to their normal state after the jar on the bottom has been replaced.

Electricity Problems

Occasionally, the flashing lights on your KitchenAid blenders aren’t even error indicators.

If there is an issue with the electricity moving through the outlet you are using for the blender, flashing lights can be an issue.

Damage to the outlet or a short in the circuit is a potential culprit.

Plug your blender into a different outlet to check if you were right.

If the flashing lights stop, the outlet can be deemed the criminal behind the abovementioned issue.

Stuck Key

The main reason a blender’s key gets stuck is because of trapped air bubbles.

You can resolve this by striking a solid balance between the liquid you wish to mix with the ice and the ice itself.

In addition, most decent blenders are equipped with a pulse feature – that comes in very handy in these situations.

Locked Motor Rotor

Is your blender plugged in, but it doesn’t do anything even when the POWER is one?

Assuming all indicator lights are blinking at the same time, you have a locked motor rotor situation on your hands.

Press POWER before unplugging the blender.

Plug it back into a functional socket and then choose POWER.

Is the pitcher secured properly?

If your Kitchen aid blender lights flashing, then you should check the pitcher.

Inspect the pitcher whether it is secured properly to the base.

If it is not, the Kitchenaid blender light may blink.

For the right functioning of the blender, the pitcher should be fully in place.

6 Methods to Solve the Flashing Lights Problems

Method 1: Replacing the Fuse

An easy first repair should be changing the fuse.

For that, you have to get the correct fuse first.

Start by removing the small rubber legs on the base of the blender.

Simply pull on them. Unscrew them and take off the bottom.

You should see a red wire with a coupling coming down from the electronic panel.

A plastic 2-piece cover should be between them.

Pull apart the cover and look for the fuse.

Method 2: Replacing the Stuck Key

Replacing the keys on a blender is quite simple.

But you need a screwdriver set for this one.

We recommend a screwdriver set rather than a solitary tool as you may end up needing a few different types of screws along the way.

a. Detach it from the power

Unplug the blender from the socket as your first and foremost step.

Before performing any sorts of checkups or diagnostics, make sure to disconnect the electronic gadget from an active power source.

And by unplugging, we meant the whole deal – don’t just switch the power off.

b. Take out the blender’s footpads

On a few blenders, the screws are hidden under the footpads.

Therefore, you can only access them by taking out the footpads.

However, there is no need to remove the footpads if the motor base’s screw has already been exposed.

Once you can see the screws, select the best screw size for the job because we will unscrew ourselves.

The screws are generally four in number, but they fluctuate depending on the manufacturer.

c. Detach the panel clips

Once you have successfully removed the base of a motor, the next challenge is to remove some wire sets that contact the panel via clips. Yours can be two, three, or any other number.

To remove these clips, squeeze their base as you lift them.

Don’t squeeze too hard, as a bit of force goes a long way here.

d. Unfasten the screws from the panel

The panel is what you have left after unclipping all the wires.

This panel needs to be removed before anything else.

For that, separate the screws securing them in place with the correct screwdriver head.

Once the screws are off, you have to keep everything in a safe location, so you don’t miss anything later.

Raise the panel ever so gently, so you don’t unintentionally mess with a few of the welded circuits.

e. Take off the second panel

Your blender might also have another panel with two or more screws.

You have to use the correct screwdriver to remove them and once you are done, gently lift it up.

Once the panel has been opened, you can better understand what was working on the switches.

Check if the plastic nub generally pushes a social button.

If it is twisted, it isn’t easy to restore the blender once pressed.

Just use a screwdriver to fix the twisted nub to make things right.

f. Reassemble the parts

Confirm that the button can be pressed without problems.

If yes, assemble the parts once again and make sure you do it with utmost care and precision.

Screw on the panels the same way you took them out.

Now, clip the wires back by softly pressing the clips and positioning them on the blender’s connector spots.

After everything is done, screw the motor base in place, and you should be done!

The whole process should not take more than 20 minutes.

However, if you feel like you aren’t prepared to take on such a responsibility, get the KitchenAid blender checked by a technician.

Method 3: Resetting the Blender

If you have confirmed that the blender got overloaded while blending chunky ingredients, this is how to approach that.

In that situation, the blender will shut down automatically to prevent damage to the engine.

Press the OFF switch to reset the equipment.

Next, remove the pitcher from the blender’s base and divide the contents of the jar into smaller batches.

Try adding a little liquid to the pitcher, as this can help.

Method 4: Freeing the Blades

If jammed, the blender’s engine will stop functioning to avoid damage.

First, press the OFF switch to reset your KitchenAid blender.

Next, take off the pitcher from the blender’s base and remove or break up the contents at the base to free up the blades.

Method 5: Checking the Electrical Circuits

Have a look if the blender is connected to a grounded three-prong outlet.

If yes, press POWER and unplug the blender.

Then, plug it into the same outlet again before pressing POWER.

Check the circuit breaker or fuse if the blender doesn’t start working at this point.

Method 6: Place the pitcher on the base precisely

If your Kitchenaid blender pitcher might not be fully in place, the blender is likely to blink the light.

For this, ensure it is all the way in, and the lid is aligned properly.

Sometimes you need to reset the blender.

For resetting the blender turn the blender to the “OFF/O” position and back to your desired setting.

Final Thoughts

All solutions stated above are a generalized view of fixing blinking lights on the KitchenAid blender.

In reality, it is difficult to be accurate about what the flashing lights mean without knowing the blender’s model number.

However, your blender’s owner manual should have instructions on what these flashing indicator lights mean and how you can solve them.

If you have misplaced your owner’s manual, get in touch with KitchenAid directly for assistance.

Happy Blending!!!




Related Articles:

KitchenAid Blender Stuck to Base?

KitchenAid Blender Coupling Melted?

KitchenAid Blender Smells Like Burning?