Amana

Amana Washer Stuck on Final Spin?- Here’re 9 Fixes!

Amana Washer Stuck on Final Spin
( Disclaimer: As an Amazon Associate, we earn commissions from qualifying purchases at NO additional cost to the customer.)                                          

Most people don’t care about their washers.

They just put their clothes in, add in their detergent, fabric softener, and expect them to work properly.

Sometimes, they don’t.

What if your Amana washer is stuck on the final spin?

It may be because of the shifter issues or the timer may be faulty.

There are various of reasons why the Amana washer stuck on the final spin.

The main thing for this issue is the load is unbalanced.

The most common problem that people face is when the washer gets stuck on the final spin.

This article will show you how to deal with this issue.

We will show you how you can fix this issue by following simple steps.

Amana Washer Stuck on Final Spin- Causes

In this section, we will show you what may be the reasons that your Amana washer is stuck on the final spin.

After reading this article you may not need to call the technician, by following simple steps you will be able to analyze the causes for why your Amana washer is stuck on final spin and you will be able to fix them.

Unbalanced loads or overload

If your Amana washer is stuck on the final spin, there could be an unbalanced load.

The clear reason is you put too much laundry to wash and it’s also too tightly in the washer. 

If you put a large load, the washer has slow spin speeds.

It can play with the sensors and the control panel that lead to the machine stopping altogether. 

For this, you need to take out some of the cloth items and reset the washer to see if that solve the problem.

There are other various reasons for unbalanced loads besides a lot of laundries.

It can also happen due to washing one bulky item, like a comforter, alone in the washer.

In this case, you can add a few more items and distribute the weight and balance in your washer. 

You may also want to check the washer is placed on a proper level floor.

The problem also arises due to washers moving or losing a foot peg.

The lid lock light is flashing.

The lid can seem to be closed but is not locked, and hence will not spin.

Look for anything that might be in the path.

To remove any detergent or lint, wipe clean the lock striker (the portion on the lid that fits into the lid lock) with a moist cloth.

Worn out skate plate shoes

One possible cause of the unbalance is worn-out skate plate shoes.

This is more likely to happen on an older system.

You can inspect the shoes, but you will need to open the washer to do so.

When you open the washer, you’ll notice that the washer tub is supported by three legs.

The shows are located between the pedestal’s top and the skating plate.

Lift the skate plate one inch and insert something as a wedge.

Examine each shoe by snapping it out of place.

Imbalance issues

Sometimes trying to fix the imbalance of the washer may not work.

You should go for recalibration.

Occasionally, the system in the washer messages conveys to the control board that the washtub is having difficulty for spinning the clothes.

Regardless, recalibrating it may resolve the issue.

Some brands come with essential calibration for the right balanced load or the right amount of water in the tub for the load. 

Make sure the washer is turned off properly and unload clothes and empty the water. 

The timer

A faulty of timer may lead to your washer stuck on spin.

But you can fix this issue with DIY. 

For this, you have to take the control panel out of the washer to test the timer. 

Most panels are easy to get into. 

You need to locate the timer first.

The timer is located behind the knob with a few screws and a wire harness. 

You need to remove the front knob before the timer can be accessed.

To test the timer you will need a multimeter and check if it has continuity. 

Replace the timer if it’s failed. You just need to connect a few wires which is very easy. 

Amana Washer Stuck on Final Spin?- Fixes

To clear out any detergent, you need to fill up the machine with warm water and use self-cleaning settings in your Amana washer.

When utilizing rise mode for medium to big loads of laundry, you must do this in the absence of any other laundry and with little to no soap.

Simply straightening the crooked pipe or clearing the dirt off the clogged drainage filter can solve drainage problems with your washer.

But sometimes, you might have to swap out the complete filter.

Even though it is very expensive, this is still a less expensive option than purchasing a new washer.

Switch out the control board.

Since it is the most expensive option, it should only be used as a last resort.

However, if the issue isn’t with water entry or outflow and reducing the load of laundry has no impact at all, the control board is most likely to blame.

The board should then be replaced to fix the problem.

Drive Belt

To resolve the issue, you need to inspect the drive belt to determine whether it is broken or if loose on the pulleys.

You need to replace the drive belt, if the drive belt is broken or loose.

Motor Coupling

The washer transmission is connected to the motor by the motor coupling.

If your washer is overloaded, the motor coupling will break to protect the motor and gearbox.

Normal wear and tear can also cause the motor connection to fail.

Inspect the motor coupling to check whether it is damaged.

Replace the motor coupling if it is damaged.

Lid Switch Assembly

The lid switch assembly prevents the washer from spinning if the lid is open,.

The lid switch component must work appropriately for the washer to spin.

Check the lid switch for continuity to check if the lid switch assembly is faulty using a multimeter.

Replace the lid switch if it doesn’t have continuity.

Drive Motor

The drive motor could be faulty.

However, the drive motor is almost unlikely to blame for this problem.

Check all of the more often faulty washer components before replacing the drive motor.

If none of those components are faulty, replace the drive motor.

To verify if the drive motor is faulty, first ensure that it is receiving electricity.

Replace the drive motor if it hums but does not operate, is noisy, or does not turn easily.

Rotor Assembly

The rotor and stator interact to generate a powerful electromagnetic field that turns the tub in either direction.

The washer may not spin or agitate if the rotor’s magnets are destroyed or if any part of the rotor is malfunctioning.

Inspect the rotor for damage to determine if it is defective.

Replace the rotor if it is damaged.

Door Latch

The washing door is kept closed while in operation by the door latch.

The washer can start working after the door is shut.

The door switch will stop the washer from working if the washer door is not fastened shut.

The washer won’t spin or start if the door latch is broken.

Electrical or mechanical failures of the door latch are both possible.

Check for damage to the door lock.

Replace the door latch if it is broken or does not close securely.

Using a multimeter, check the continuity of any switches on the door latch to see whether it has electrically failed.

Replace the switch if none of the switches exhibit continuity when actuated.

Door Lock Motor and Switch Assembly

During operation, the door lock helps the washer door shut throughout the working of washer.

The washer can start working after the door is closed.

The washer door will not latch properly if the door lock is faulty.

Mechanical or electrical failure of the door lock is possible.

Examine the door lock for damage.

Replace the door lock if it is damaged or does not latch properly.

To see if the door lock has failed electrically, use a multimeter to check the continuity of each of the door lock switches.

If one of the switches does not have continuity, it should be replaced.

Motor Control Board

The motor control board is the component that power the motor.

The washer might not operate correctly or might not operate at all if the motor control board is faulty.

First, look for any burned-out components on the control board.

Verify that the control board is powering the motor to see if the motor control board is faulty.

Replace the control board if it is powered but not driving the motor.

Transmission

If the Amana washer stuck on final spin, the washer transmission may worn out or faulty.

Transmissions contain gears that can fail, causing the washer not to spin or agitate.

This, however, is nearly never the case.

Check all of the other components in this troubleshooting guide before replacing the transmission.

Consider changing the transmission if the motor is turning the transmission but the washer is not spinning or agitating.

 

Sources:

https://www.amana.com/articles/why-your-washer-wont-spin.html

https://www.justanswer.com/appliance/fehm9-amana-washing-machine-stuck-final-spin-can-t-move.html

 

 

Related Articles:

Amana Washer Makes Loud Noise When Spinning?

Why is Amana Washer Takes Forever To Wash?

Amana Washer Not Draining All The Way?